尿素装置液位仪表失真分析及处理

介绍了尿素装置中3起液位仪表失真案例,分析了故障现象和设备工况,确定失真原因,采取了相应的处理措施,解决了仪表故障。     

稀土石膏常压酸化法制备硫酸钙晶须的研究

以含稀土的石膏为原料运用常压酸化法合成硫酸钙晶须,探讨了不同工艺条件对生成的硫酸钙晶须形貌的影响,同时还考察了晶型助长剂的种类和晶型助长剂的含量对硫酸钙晶须生长的影响,利用SEM和XRD分别对硫酸钙晶须的表面形貌、物相特征做了表征分析。实验得到制备硫酸钙晶须的最佳的反应条件：稀土石膏质量浓度为0.22 g/mL、反应时间为25 min、盐酸浓度为2.8 mol/L、反应温度为70 ℃、陈化时间为4 h,在此条件下合成的硫酸钙晶须平均长度为61 μm,平均长径比为30.5;通过对比实验选出了CuCl₂作为促进硫酸钙晶须生长的助长剂,在添加5%（质量分数）的CuCl₂的情况下可使硫酸钙晶须长径比从30.5增至41,长度从61 μm增至81 μm。     

强碱三元复合驱色谱分离及其影响因素——以大庆油区喇嘛甸油田为例

三元复合驱油体系中驱油剂的协同效应,会使油水间的界面张力大幅度下降,原油采收率大幅度提高;但三元复合驱油体系的色谱分离现象也会破坏其协同效应和完整性,揭示色谱分离现象及其影响因素对于改善三元复合驱油效果具有十分重要意义。以油藏工程和分析化学理论为指导,以化学分析和物理模拟为技术途径,并以大庆喇嘛甸油田典型区块地质特征和流体性质为研究对象,开展强碱三元复合驱色谱分离现象及其影响因素研究。结果表明,采用前置高浓度聚合物段塞后,可以有效扩大波及体积,但表面活性剂与碱和聚合物之间无因次等浓距增加,色谱分离现象加剧。大庆油区喇嘛甸油田不同区块油水性质差异对色谱分离现象存在影响,原因在于部分重烷基苯石油磺酸进入油相,影响水相中浓度检测值。强碱三元复合驱油体系中表面活性剂与碱和聚合物之间色谱分离程度比较严重,碱与聚合物之间较弱。     

原子吸收光谱法测定保护渣中锰含量

采用原子吸收光谱法测定保护渣中锰含量,进行了酸度对测定的影响、试样分解、共存离子干扰、加标回收、精密度分析等试验。结果表明,锰可完全溶解于混合酸溶液中;加入氯化锶,可以消除钠、钙对锰测定的干扰;锰质量浓度在0~12.0μg/mL的范围,工作曲线线性关系良好;加标回收率较高,在97%~102%;测定结果准确度较高,与高碘酸钠光度法分析结果一致性较好。     

Effects of Undercooling and Transformation Time on Microstructure and Strength of Fe–C–Mn–Si Superbainitic Steel

Strength of Materials - A metallographic method, dilatometry, and X-ray diffraction were applied to investigate the effects of undercooling and holding time on bainitic transformation,...     

Effect of Li2O on the crystallization behavior of CaO-Al2O3-SiO2-Li2O-Ce2O3 mold slags

The effect of Li₂O on the crystallization properties of CaO-Al₂O₃-SiO₂-Li₂O-Ce₂O₃ slags was investigated. With increasing the Li₂O content, LiAlO₂ and CaCeAlO₄ were the main crystalline phases. LiAlO₂ formed for the charge compensating of Li⁺ ions to [AlO₄^5?]-tetrahedrons, and CaCeAlO₄ formed as a result of the charge balance of Ce³⁺ ions, Ca²⁺ ions, and [AlO₆^9?]-octahedrons. Increasing the content of Li₂O to 10%, the crystallization temperature was the highest, and the incubation time was the shortest. The crystallization ability was strong due to the three factors of strengthening the interaction between ions and ion groups, decreasing the polymerization degree, and increasing the melting temperature. Further increasing the content of Li₂O, the crystallization performance was obviously suppressed, because the melting temperature and the force between the cations and the anion groups decreased.     

A Complexing Agent to Enable a Wide-Temperature Range Bromine-Based Flow Battery for Stationary Energy Storage

Bromine-based flow batteries (Br-FBs) are considered one of the most promising energy storage systems due to their features of high energy density and low cost. However, they generally suffer from uncontrolled diffusion of corrosive bromine particularly at high temperatures. That is because the interaction between polybromide anions and the commonly used complexing agent (N–methyl–N–ethyl–pyrrolidinium bromide [MEP]) decreases with increasing temperatures, which causes serious self-discharge and capacity fade. Herein, a novel bromine complexing agent, 1–ethyl–2–methyl–pyridinium bromide (BCA), is introduced in Br-FBs to solve the above problems. It is proven that BCA can combine with polybromide anions very well even at a high temperature of 60 °C. Moreover, the BCA contributes to decreasing the electrochemical polarization of Br⁻/Br₂ couple, which in turn improves their power density. As a result, a zinc–bromine flow battery with BCA as the complexing agent can achieve a high energy efficiency of 84% at 40 mA cm⁻², even at high temperature of 60 °C and it can stably run for more than 400 cycles without obvious performance decay. This paper provides an effective complexing agent to enable a wide temperature range Br-FB.